電氣設備翻譯—中英文對照

PRS-711微機線路成套保護裝置
PRS-711裝置為微機實現的數字式高壓線路快速保護裝置，適用于110kV及以下電壓等級、中性點直接接地、故障時三相跳閘能夠滿足系統穩定性要求的線路。
裝置保護的基本配置包括了完整的距離和零序保護，更可在此基礎上配置縱聯距離及縱聯零序保護，用于要求全線速動的場合。裝置可與專用收發信機配合，通過高頻載波實現縱聯保護；還可內置光端機，通過光纖通道實現縱聯保護。各型裝置均設有三相一次重合閘功能，自帶跳合閘操作回路以及交流電壓切換回路。
PRS-711裝置采用先進的硬件平臺和完善的軟件設計，裝置的軟件功能配置靈活完備，縱聯保護的通道接口方式設置可充分滿足用戶需要，且通信可靠性高，再加上強大的輔助功能支持，使整套保護裝置具有更優異的性能。
PRS-711微機線路成套保護裝置
PRS-711裝置提供了豐富的保護元件，可根據用戶需求進行配置。主要保護元件包括：
縱聯距離保護/縱聯零序保護
突變量距離繼電器
四段相間距離/三段接地距離
四段零序方向過流/零序反時限過流
不對稱故障相繼速動/雙回線相繼速動保護
合閘于故障保護
弱饋線保護
振蕩閉鎖
電壓斷線檢測和緊急狀態保護
三相一次自動重合閘/檢同期手合
滑差或無滑差閉鎖低周減載/低壓減載
過負荷保護
TA異常/角差異常/TWJ異常告警功能
 裝置包含由超范圍距離方向和零序方向元件構成的全線速動縱聯保護，動作速度快，全線速斷時間小于25ms。
 裝置的兩個CPU板具有獨立的起動元件，兩個起動元件均動作時整套保護裝置才能出口，保護安全性高。
不受振蕩影響，在系統振蕩（無故障）時可靠不誤動，在振蕩中又發生故障時仍能保持保護動作的快速性與選擇性。
不受弱饋側安裝的影響，具備在弱電源側的正確保護功能。
在手動和自動合閘時有合閘于故障保護快速切除全線各種故障。
在TV斷線時可投入可靠的緊急狀態保護，確保裝置性能。
裝置采用高性能的平臺設計，可靠性高，抗干擾能力強。
采用32位浮點DSP和16位高精度A/D采樣，運算與邏輯功能強大。
單元化設計、模塊化結構，可擴充性強。
大屏幕漢字彩色液晶顯示、直觀友好的界面菜單、完備的過程記錄，信息詳細直觀，操作調試方便。
以高可靠性工業級器件為主體，采用自動監測、補償技術提高硬件電路穩定性、可靠性。
封閉、加強型單元機箱，多層屏蔽等抗振動、抗強干擾設計。
充分發揮微機保護的優越性，具備豐富的輔助功能，體現人性化設計。
完善的事故分析功能，包括保護動作事件記錄、故障起動記錄、故障錄波記錄、裝置運行記錄、開入變位記錄，及裝置自檢記錄和閉鎖記錄等，可再現故障情況及故障時保護裝置的動作行為。（裝置可保存最新的128次動作事件記錄和32次錄波記錄。）
靈活的后臺通信方式：三個TCP/IP以太網接口，兩個RS485接口，兩個CANBUS接口，一個串行打印口，一個GPS脈沖接入口（差分輸入或空接點輸入，對秒、分脈沖和IRIG-B串行編碼三種校時方式自適應）。支持電力行業標準IEC60870-5-103規約。通訊速率可整定。
縱聯保護通道說明
裝置的縱聯保護能同各種通道通信設備（繼電保護專用收發信機及復用載波機等）接口。發、停信控制采用一副接點，不發信即為停信。當用于專用閉鎖式時，通道邏輯由保護裝置實現，收發信機的停信和發信完全由保護控制。
裝置的縱聯保護的收發信還可以通過光纖通道實現，用于允許式保護。保護裝置與光纖通道相連實現方案有兩種，一是采用接點方式，同時外配光纖接口裝置，保護裝置收發信節點與光纖接口裝置相連實現收發信功能；二是增加內置光纖接口板，直接與光纖通道相連。

PRS-711 Microcomputer-based Line Whole-set Protection Device
PRS-711 device is microcomputer controlled fast protection device for digital high voltage lines, which is applicable for lines with the voltage grade equals to and below 110kV, neutral point direct earthing, and three-phase tripping when fault occurs to keep the stability of the system.

The basic configuration of device protection includes whole distance and zero sequence protection, and the configuration of distance pilot protection and zero sequence pilot protection is available for whole line quick-acting required occasions. Together with dedicated transreceiver, the device can achieve pilot protection though high frequency carrier; it can also build the optical transmitter and receiver inside, and achieve pilot protection through fiber channel. All types of devices have three phase one shot reclosure function, and with tripping and closing control circuit and AC voltage switching circuit.

PRS-711 device adopts advanced hardware platform and perfect software design, the software function configuration of the device is flexible and complete, the interface mode setting of the pilot protection channel can fully meet the customer’s requirements, the communication is very reliable, and supported with powerful auxiliary functions, all of which provide the whole protection device with more excellent performance.
PRS-711 Microcomputer-based Line Whole-set Protection Device
PRS-711 device provides a variety of protection elements, which can be configured according to customer’s requirements. The primary protection elements include:
Distance pilot protection/Zero sequence pilot protection
Variation distance relay
Four-zone phase-to-phase distance/Three-zone earth distance
Four-zone zero sequence directional over-current/Zero sequence inverse time over-current
Unsymmetrical fault sequent quick-acting/Double lines sequent quick-acting protection       
Switch onto fault protection
Weak feeder protection
Power swing
Voltage break detection and emergency state protection
Three phase one shot automatic reclosure/Synchronism check manual close
Slip or no slip lock low frequency load shedding/under voltage load shedding
Over load protection
TA abnormal/angular difference abnormal/TWJ abnormal warning function

The device has whole line quick-acting pilot protection consists of overrange range direction and zero sequence direction elements, which is quick-acting, and the quick break time of the whole line is less than 25ms.
Two CPU plates of the device have independent starting elements, only both starting components are active, the whole protection device opens, so the protection is of high security.
Not affected by oscillation, no false operation at system oscillation (no fault), and can still keep the rapidity and selectivity of the protection action when fault occurs again in oscillation.
Not affected by the installation of weak feed backside, with right protection function for the week power backside.
The switch onto fault protection removes all faults of the whole line rapidly when switching on manually and automatically.
Can input reliable emergency state protection at TV breaking time to ensure the performance of the device.
The device is designed with high performance platform, with high reliability and powerful anti-interference capability. Sampling with 32 bits floating point DSP and 16 bits high precision A/D, and has powerful calculation and logic function.
 Unitized design, modular structure, with high expandability.
 Large-screen Chinese character color liquid crystal display, intuitive and friendly interface menu, complete process record, intuitive detailed information, and convenient operation and debugging.
 With high reliability industrial level devices as the main body, adopts automatic monitoring and compensation technology to improve the stability and reliability of the hardware circuit.
Close and reinforced unit chasis, multilayer screen, etc. anti-vibration and anti strong interference design.
Give full play to the superiority of microcomputer protection, with a variety of auxiliary functions, and reflects the humanized design.
 Perfect fault analysis function, including the protection of action event records, fault starting records, fault recording records, device operation records, opening-inserting phase change records, device self inspection records, and lock records, etc., can reappear the status of the fault and the action of the protection device at the fault time. (the device can store the latest 128 action event records and 32 recording records.)
Flexible background communication mode: three TCP/IP Ethernet interfaces, two RS485 interfaces, one CANBUS interfaces, one serial print interface, one GPS pulse access interface (differential input or idle contact input, self-adapting to the three timing modes, namely PPS, PPM, and IRIG-B serial code). Supports IEC60870-5-103 standard of the power industry. The communication speed can be set.
Introduction of Pilot Protection Channel
The pilot protection of the device can connect with all kinds of channel communication devices (dedicated transreceivers and multiplex carriers for relay protection). Sending and stopping control with one contact point, and not send is stop. When applied to the dedicated lock mode, channel logic is achieved by the protection device, and the stopping and sending of the transreceiver is completely controlled by the protection.

The pilot protection sending and receiving of the device can also be achieved though fiber channel, which is available for permissive protection. There are two solutions for the connection between the protection device and the fiber channel, one of which is the connection point mode, meanwhile, equips with optical interface devices, connects the receiving and sending connection of the protection device with the optical interface device to realize the receiving and sending function; the other is adding built-in optical interface plates to connect directly with the fiber channel.
 

            譯雅馨深圳翻譯公司 用心翻譯  值得信賴   全國統一熱線：400-8808-295